ProBasics Adjustable Lightweight Full-Electric Hospital Bed with Full Rails & Aruba-200 Mattress
A complete full-electric homecare bed package featuring powered upper-body, knee, and bed-height adjustment, a lightweight split-frame design, reduced-gap full-length bed rails, and an Aruba-200 contour foam mattress.
Full-Electric Adjustment Powered controls adjust the upper-body section, knee section, and overall bed height.
Full-Length Rails Includes one pair of PB6034 reduced-gap full-length rails with four crossbars.
Aruba-200 Mattress Includes a sculptured 36 × 80-inch contour foam mattress rated for users up to 350 lb.
Split-Frame Design Head and foot sections separate to support delivery, setup, cleaning, and servicing.
Bed and Package Specifications
Review the sleep surface, bed height, mattress capacity, total load, room clearance, rail coverage, and transfer requirements before ordering.
Mobile users: swipe left or right to view the full table. The Specification column remains visible.
ProBasics PBFEB-FRARBPKG Specifications
| Specification |
Manufacturer-Listed Details |
| Package SKU |
PBFEB-FRARBPKG |
| Bed Model |
PBFEB |
| Bed Format |
Two-motor full-electric homecare bed |
| Powered Functions |
Upper-body elevation, knee-section elevation, and overall bed-height adjustment |
| Sleep Surface |
80 in. L × 36 in. W |
| Overall Bed Size |
87 in. L × 36 in. W |
| Published Minimum Deck Height |
12.75 in. without casters |
| Published Maximum Deck Height |
21.5 in. with casters |
| Total Distributed Bed Capacity |
450 lb, including the user, mattress, bedding, accessories, and all other deck loads |
| Mattress Capacity |
350 lb |
| Maximum User Weight |
Up to 350 lb, while remaining within the bed’s 450 lb total distributed load limit |
| Full Rails |
One pair of PB6034 reduced-gap full-length bed rails |
| Rail Length |
55 in. |
| Rail Height Above Deck |
Approximately 13.5 in. raised and 4.5 in. lowered |
| Rail Construction |
Welded steel with four crossbars and self-adjusting spring-loaded cross braces |
| Mattress |
ARUBA-200 single-layer contour foam mattress |
| Mattress Dimensions |
36 in. W × 80 in. L |
| Casters |
Two locking and two non-locking casters |
| Motor System |
ETL-approved low-voltage DC motor box and high-low motor |
| Hand Control |
Large-button wired hand pendant |
| Emergency Height Adjustment |
Manual crank located at the foot end |
| Emergency Battery Backup |
9V battery-backup provision; battery not included |
| Positioning Capability |
Trendelenburg and reverse-Trendelenburg setup capability |
Published minimum and maximum deck heights use different caster configurations. Confirm the actual installed deck height, mattress-top height, transfer height, and rail clearance before delivery.
Important Capacity Information
The bed’s 450 lb rating is a total distributed load limit. It includes the user, mattress, bedding, positioning products, accessories, and any other items placed on the sleep surface.
The included Aruba-200 mattress is rated for a maximum user weight of 350 lb. This package must not be advertised as a 450 lb patient-capacity bed.
Why Choose the ProBasics Full-Electric Bed Package?
A standard household bed does not provide powered deck-height adjustment or independent upper-body and knee positioning. The ProBasics full-electric bed allows the user or caregiver to adjust these positions using a simple large-button pendant.
The welded steel split-frame design supports residential delivery and servicing, while the full-length rails and Aruba-200 mattress create a complete package for users who have been professionally assessed for continuous rail coverage and contour-foam support.
Key Features
- Two-motor full-electric operation
- Powered upper-body adjustment
- Powered knee-section adjustment
- Powered high-low adjustment
- Large-button hand pendant
- Welded steel split-frame construction
- Quick-release motor-box design
- Scratch-resistant head and foot ends
- Recessed head-spring and foot components
- Manual emergency height crank
- 9V emergency-backup provision
- Two locking casters
- Two non-locking casters
- Reduced-gap full-length rails
- Four-crossbar rail design
- ARUBA-200 contour foam mattress
- Trendelenburg setup capability
- Reverse-Trendelenburg setup capability
Practical Benefits and Common Uses
- Powered positioning for users requiring frequent position changes
- Bed-height adjustment for appropriately assessed transfers and care
- Upper-body elevation for comfort and prescribed positioning
- Knee elevation for supported resting positions
- Full-length rail coverage for carefully assessed users
- Sculptured foam surface supports airflow and pressure redistribution
- Split-frame construction supports delivery into residential spaces
- Suitable for homecare, assisted-living, and long-term-care environments
- Appropriate for rental programmes when professionally installed and assessed
Standard Package Contents
- ProBasics PBFEB head and foot spring sections
- Head and foot bed ends
- Low-voltage motor box and high-low motor
- Large-button wired hand pendant
- Two locking and two non-locking casters
- Manual emergency height-adjustment crank
- One pair of PB6034 reduced-gap full-length rails
- One ARUBA-200 contour foam mattress
- Assembly and operating documentation
- Manufacturer warranty information
The 9V emergency-backup battery, bedding, sheets, overbed table, trapeze, rail pads, and other accessories are not included unless specifically stated.
Aruba-200 Contour Foam Mattress
- 36 × 80-inch Group 1 foam mattress
- Single-layer sculptured foam core
- Three support zones for the head and shoulders, torso, and lower extremities
- Sculptured surface supports airflow around the body
- Designed to support comfort and pressure redistribution
- Durable stretch-nylon cover
- Fluid-resistant, washable surface
- Waterfall zipper helps protect the foam core
- Urethane laminate helps reduce friction and shear
- Reinforced non-slip bottom
- Elastic corner straps help secure the mattress to the deck
- 350 lb weight capacity
- Compressed, rolled, and boxed for transportation
Full-Rail and Entrapment Safety
Full-length bed rails can create entrapment, climbing, over-the-rail fall, and injury hazards. Reduced-gap construction does not eliminate these risks.
A qualified healthcare professional or trained equipment provider should assess the user’s cognition, mobility, body size, behaviour, transfer method, mattress compression, rail spacing, and entrapment risk before the rails are installed or used.
Full rails may make independent entry and exit difficult. They are not restraints and must not be used to confine a user.
Reassess all openings whenever the mattress, rails, overlays, positioning products, bed configuration, or user condition changes. Remove the rails from service if they are loose, damaged, incorrectly positioned, or create an unsafe opening.
Usage and Safety
The bed should be assembled, installed, inspected, and demonstrated by trained personnel. Read the complete manufacturer instructions before operating, repositioning, cleaning, or servicing the equipment.
Lock both locking casters before transfers, personal care, or leaving the bed stationary. Adjust the bed to the safest practical height when the user is unattended, according to the care plan.
Keep hands, feet, bedding, clothing, tubing, electrical cords, children, pets, and loose objects away from moving deck sections, motors, hinges, rails, and pinch points.
Do not exceed the bed, mattress, rail, or accessory capacity. Disconnect electrical power before cleaning beneath the bed or performing maintenance.
Setup, Positioning, and Power-Outage Operation
Installation and Setup
- Confirm sufficient room clearance around all sides of the bed
- Connect the head and foot spring sections according to the instructions
- Install and secure the bed ends, motor box, high-low motor, and pendant
- Confirm all shafts, pins, clips, and electrical connections are engaged
- Install the casters and test both caster locks
- Place and secure the mattress on the deck
- Install rails only after completing a rail-suitability and entrapment assessment
- Test every powered, manual, rail, and caster function before use
Trendelenburg Setup
- Trendelenburg capability is created through bed-end setup
- It is not a separately powered pendant function on this model
- Configuration should be completed by trained personnel
- Use only when clinically appropriate and authorized
Power Failure
- A 9V battery may provide limited emergency positioning
- The 9V battery is not included
- Battery backup is not intended for routine bed operation
- Use the manual crank for emergency bed-height adjustment
- Review the emergency procedure before the bed is placed into service
Inspection, Cleaning, and Maintenance
Routine Inspection
- Test the pendant and every powered function
- Inspect the frame, spring deck, bed ends, welds, pins, and fasteners
- Check motors, cables, cords, plugs, and strain-relief points
- Test both locking casters and inspect all caster wheels
- Inspect rails, cross braces, release mechanisms, and all openings
- Inspect the mattress cover for tears, damaged seams, or fluid penetration
- Confirm the mattress remains centred and secured
- Remove the equipment from service if any component is damaged or operates abnormally
Cleaning
- Disconnect electrical power before cleaning
- Use a damp cloth and an appropriate healthcare cleaner
- Follow the cleaner manufacturer’s dilution and contact-time directions
- Do not saturate motors, controls, cables, plugs, or electrical connections
- Do not use a hose, pressure washer, or abrasive cleaner
- Clean the mattress cover according to its instructions
- Allow all surfaces to dry before reconnecting power or making the bed
Frequently Asked Questions
What is included in PBFEB-FRARBPKG?
The package includes the standard-height PBFEB full-electric bed, one pair of PB6034 reduced-gap full-length rails, and one ARUBA-200 36 × 80-inch contour foam mattress.
Is this the low-bed version?
No. This package uses the standard PBFEB bed. The manufacturer lists a 12.75-inch minimum deck height without casters and a 21.5-inch maximum deck height with casters.
Is the patient-weight capacity 450 lb?
No. The 450 lb figure is the bed’s total distributed load limit. The included Aruba-200 mattress is rated for users up to 350 lb, so the package should be treated as a maximum 350 lb user-capacity system.
Are full-length rails suitable for every user?
No. Full rails can create entrapment, climbing, transfer, and over-the-rail fall hazards. A patient-specific assessment must confirm that they are appropriate with the installed mattress and the user’s care plan.
Will the bed work during a power outage?
The bed includes a 9V emergency-backup provision and a manual height-adjustment crank. The 9V battery is not included and emergency backup is not intended for normal operation.
Manufacturer Warranty
- Bed frame: 5-year limited warranty
- Bed motor and mechanical/electrical components: 2-year limited warranty
- PB6034 full rails: 2-year limited warranty
- Aruba-200 foam core: 2-year limited warranty
- Aruba-200 mattress cover: 1-year limited warranty
Warranty coverage is subject to current manufacturer terms, exclusions, proof-of-purchase requirements, normal-wear exclusions, and authorized-service procedures.
Manufacturer Resources
Review the official product information and entrapment guidance before assembling, installing rails, operating, cleaning, or servicing the bed.
Need Help Confirming Capacity, Rails, or Installation?
Contact Med Supplies at 780-425-5599 for help reviewing user weight, mattress capacity, transfer height, room clearance, rail suitability, entrapment risk, delivery access, and installation requirements.
780 409-1509
Get directions
